Answering now, 24 hours a dayMobile locksmith based in Chelsea SW307520 643913
IDNChelsea LocksmithLocal locksmith for SW3 and SW10 07520 643913

Euro Cylinder Replacement Chelsea uPVC and Composite

Get a euro cylinder quote in Chelsea No call out fee

Preferred contact method

We call you back with a price before anyone sets off. Nothing is added on the doorstep.

Euro cylinder replacement in Chelsea costs £40 to £65 with us, fitted, and we usually reach SW3 and SW10 homes within 30 minutes of your call. We measure your existing cylinder on the door, fit a correctly sized replacement on uPVC, composite or timber doors, and offer standard or TS007 3 star anti snap cylinders, keyed alike if you want one key for several doors. Changing the cylinder alone makes every old key useless without replacing the rest of the lock. There is no call out fee, and the price is agreed on the phone before we travel. If the handle or mechanism is also faulty, see our uPVC door lock repair page.

  • DBS checked locksmith
  • Public liability insured
  • Over 5 years working in Chelsea
  • Price agreed before work
  • No call out fee

What a euro cylinder is and why it is swapped so often

Look at a uPVC or composite door and you will see a keyhole set in a small barrel that passes right through the door below the handle. That barrel is the euro cylinder. It holds the key pattern, and when you turn the key a small cam in the middle drives the locking mechanism inside the door.

Because the key pattern lives only in the cylinder, it is the cheapest part of the lock to replace when keys go missing. You get completely new keys, the multipoint mechanism stays as it is, and the job typically takes well under an hour. In Chelsea you find euro cylinders on back doors of townhouses, on mews house entrances, on many flat doors in newer blocks and on almost every patio door.

Measuring a euro cylinder: getting the size right

Euro cylinders are sold in sizes written as two numbers, such as 35/35 or 40/50. Each number is the length in millimetres from the centre of the fixing screw to one end. Getting this right is the single most important part of the job, because a cylinder that sticks out past the handle plate is easier to attack and looks careless.

  1. Find the fixing screw

    On the edge of the door, level with the cylinder, there is a long screw through the lock faceplate. That screw marks the centre point of the cylinder.

  2. Measure each side

    From the centre of that screw, measure to the outside face of the cylinder, then to the inside face. Those two figures give the size, for example 40 outside and 50 inside.

  3. Check against the handle plate

    Ideally the new cylinder ends flush with the outer handle plate, or no more than a couple of millimetres beyond it. We pick the size that achieves this, not simply a copy of the old one.

  4. Note the cam position

    Some multipoint locks and older timber mortice cases need a particular cam type. We check it before removing anything.

You are welcome to send a photo of the cylinder and the door edge on WhatsApp before we come. It helps, but we still measure on the day.

Euro cylinder prices in Chelsea

Prices include the cylinder and fitting, there is no call out fee, and the figure is confirmed before we travel.

JobTypical price
Euro cylinder change
Standard to TS007 3 star anti snap, measured to fit
£40 to £65
Snapped or stuck key removed
Before the cylinder is changed, if a key has broken inside
£35 to £60
uPVC gearbox or multipoint mechanism
If the mechanism has failed too
£55 to £115
Keyed alike sets for several doors
Depends on number and grade of cylinders
Priced on the phone

Prices include parts and labour. The lower figure is a standard daytime job, the higher figure covers nights, weekends and high security parts. Your exact price is confirmed on the phone before we travel, with no call out fee. See the full Chelsea price list.

Offset cylinders: when one side is longer than the other

Doors are rarely symmetrical. A composite door with a thick outer skin, or a uPVC door with a deep internal frame, often needs a cylinder with sides of different lengths. These are called offset cylinders, and sizes such as 40/45, 35/50 or 45/55 are common.

An old offset cylinder that was fitted the wrong way round, or a symmetrical one used where an offset was needed, is something we see regularly when we take over a door from a previous fitter. The outside end ends up proud of the handle and the inside thumbturn sits too close to the door. Fitting the correct offset fixes both problems at no extra cost beyond the cylinder price.

Key both sides, thumbturn or half cylinder?

The size is only half the choice. The other half is how the cylinder works from the inside.

Cylinder typeHow it worksBest suited toThink about
Key and keyKey needed on both sidesDoors with glass panels or a letterbox near the lockYou need a key to get out, so keep one nearby but out of reach from outside
Key and thumbturnKey outside, a small turn knob insideFlats and homes where quick exit mattersAvoid where the turn could be reached through glass or a letterbox
Half cylinderKey on one side onlyGarage doors, gates and some cupboardsNot for main entrance doors
Double key cylinder with emergency functionOpens from one side even if a key is left in the otherHouseholds where a key is often left in the insideAsk for this when ordering, it is not standard on every brand

In mansion flats near Sloane Avenue, where the flat door is often the only way out, a thumbturn inside is usually the safer everyday choice. In a townhouse back door with a large glazed panel, key both sides tends to make more sense.

Standard or 3 star: choosing the grade of cylinder

A basic euro cylinder does its job of keeping the door locked, but older and cheaper ones have a known weakness against forced attack. Cylinders tested to TS007 and given the 3 star mark, or tested to Sold Secure SS312 Diamond, are built to resist that. The price difference is the gap between the bottom and top of our £40 to £65 range, and for an outside door we recommend the higher grade. Our anti snap locks page explains the ratings in detail, and our Ultion cylinder page covers one well known 3 star brand.

For internal doors, a cupboard or a garden store, a standard cylinder is fine. You do not need to spend the same on every lock in the house.

One key for every cylinder in the house

Euro cylinders are the easiest locks to key alike. If your front door, back door, patio door and side gate all use cylinders, they can share a single key. That is popular with families in houses near Royal Avenue and with landlords who hand a set to an agent. Keyed alike sets are often ordered in, so we will tell you on the call whether we can fit them that day or on a return visit.

Euro cylinder replacement in Chelsea and surrounding postcodes

We are based in Chelsea SW3 and cover the whole of SW3 and SW10, plus Chelsea Harbour and Fulham where newer flats and converted houses use plenty of euro cylinders. Prices for all our work are on the locksmith price list, and if you are unsure whether the cylinder is really the problem, our guide to why uPVC locks fail is a good place to start. You can see every other job we do on the services page.

Common questions

How do I know what size euro cylinder I need?

Measure from the centre of the long fixing screw on the door edge to each end of the cylinder. The two numbers give the size, such as 35/45. We measure again on the day so the new cylinder ends flush with the handle plate.

Can I replace a euro cylinder without changing the whole lock?

Yes. The cylinder is held by one screw and can be swapped on its own, giving you new keys while the multipoint mechanism stays in the door. Only if the mechanism is faulty does more need replacing.

How much does a euro cylinder replacement cost in Chelsea?

£40 to £65 including the cylinder and fitting. The lower end is a standard cylinder in the daytime, the higher end a TS007 3 star cylinder or an evening or weekend visit. There is no call out fee.

Is a thumbturn cylinder safe on a front door?

On a solid door it is a practical choice and makes leaving in an emergency easier. Where the thumbturn could be reached through a glass panel or letterbox, a key on both sides or a letterbox guard is the better option.

What does an offset euro cylinder mean?

It simply means the two sides are different lengths, such as 40/50. Thicker composite doors and some uPVC frames need one so the cylinder sits flush on both faces of the door.

Can my euro cylinder be changed if the key has snapped inside?

Yes. We remove the broken piece first, which is often enough on its own, then replace the cylinder if it is worn. Our broken key extraction service covers that part of the job.

Cylinder worn, lost or the wrong size?

Call 07520 643913 or send a photo of the door edge on WhatsApp and we will price the right cylinder before we come.

Related pages